Fuselage Index
General
- 29-22: Masking cockpit / Masking for Air Vents
- Fuselage Kit Arrival and Inventory
- Fuselage - Order & First Inventory! (sort of)
25 - Fuselage Bulkheads
- 25-03 -> 05: Completing Aileron Bearing bracket / Cover Ribs / Bulkheads
- 25-04 -> 05: Mid Fuse Forward Bulkhead / Cover Ribs
- 25-03: Bearing Bracket Misalignment Issue
- 25-02 -> 03: Fuselage Centre Bulkheads - Mid and Aft
26 - Lower Mid Fuselage
- 26-21: Riveting Baggage Ribs to Lower Skin and Finishing Chapter 26
- 26-20->21: Riveting Baggage Ribs to Seat Rib Bulkheads
- 26-17->20: Baggage Ribs - Step Attach Assemblies
- 26-14: Riveting Lower Skin to Seat Ribs
- 26-12->14: Gear Brace Assembly
- 26-10 -> 11: Lower Skin Preparation
- 26-02 & 26-08: Baggage Ribs (Batch #1) Preparation
- 26-03 -> 07: Seat Ribs
27 - Firewall
- 27-05 -> 07: Completing Riveting of the Firewall
- 27-04: Initial riveting of Firewall
- 27-02: Firewall Parts Preparation & Firewall Polishing
- 27 - Firewall - THE PRIMER WARS!
28 - Foreward Lower Fuselage
- 28-09 -> 10: Battery Box and Heater Vent Boxes
- 28-08 & 11: Attaching Forward Centre Bulkhead Assembly / Cover Panels
- 28-05 -> 07: Attaching bottom skins to firewall assembly
- 28-02 -> 04: Forward Fuselage Bottom Skins & Exhaust Tunnel
29 - Fuselage Sides
- 29-19: Installing Seat Back Guides
- 29-17 -> 20: Root Fairing Angles and Seat Brace
- 29-15: Riveting Side Skin Parts to the Fuselage
- 29-14 -> 16: Riveting of Side Skins to Fuselage (Forward of Spars)
- 29-14 -> 16: Riveting of Side Skins to Fuselage (Aft of Spars)
- 29-12: Initial Riveting of the Side Skins
- 29-09: Prepping side skins & Fuselage Side Components
- 29-09: JD-Air Canopy Latch
- 29-06 -> 07: Riveting Engine Mounts / Longerons
- 29-05: Control Column Assemblies
- 29-04: Riveting the Bottom Skins (again! Really this time).
- 29-06 -> 08: Fuselage Longerons and Cowl Hinges
- 29-02 -> 04: First Joining of Major Components (then take them apart again!)
30 - Aft Fuselage Attachment
- 30-06 -> 08: Tailcone Riveting to Fuselage
- 30-03: The BIG JOIN! (& initial tailcone riveting)
- Building a Fuselage Rotisserie
- 30-02: Baggage Bulkhead & Workshop Preparation for the BIG JOIN!
31 - Fuel System
- 31-06 -> 07: Fabrication & Installation of Fuel Lines
- 31-02 -> 03: Installing Duplex Fuel Selector / Fuel Line Brackets
- Fuel Line Straightening Tool
32 - Baggage Area
- 32-03: Baggage Tie Down Rings - Final Install
- 32-08: Painting the Interior of the Cockpit
- 32-04 -> 08: Baggage Floor / Side Skins / Flap Channel
- 32-07: Flap Motor Brackets - Modification
- 32-03: Initial Fit of Baggage Skins / Baggage Tie Downs
- 32-02: Flap UHMW Bearing Blocks / Flap Torque Tubes Missing
33 - Rudder and Brakes
- 33-04 -> 06: Installing Master Cylinders / Installing Rudder Pedal Assy / Wobbly centre support block / 33-12: Rudder Cable Links
- 33-04 -> 10: Brake Hoses
- Parking Brake Valve
- 33-02 -> 04: Rudder & Brake Pedals Preparation
- 33-11 -> 12: Installing rudder cable guides
34 - Flap Actuation
- 34-04: Incorrect Flap Motor Length (the value of VAF Forums & the RV Community)
- 34-02 -> 04: Flap Torque Tubes
- 32-07: Flap Motor Brackets - Modification
- 32-02: Flap UHMW Bearing Blocks / Flap Torque Tubes Missing
- 34-04: Alternate Flap Motor
35 - Upper Forward Fuselage
- 35-17 -> 19: Upper Forward Fuselage Skin Preperation / OP43 - Avionics Access Panels / Drilling Cowl Attach Hinges
- 35-08 -> 35-20: Finally installing the forward fuselage parts to the airframe
- Final Painting Chapter 35 & 37
- 35-09 ->13: Aft Panel Frame Assembly / 59-02: Power Module Parts / 42-03: Aft Tunnel Cover Modification
- 35-02 -> 07: Riveting Upper Fwd Fuse Components
- OP63 - Remote Canopy Release - Mechanism Assembly
- 33-02 -> 05: Part Prep for Upper Forward Fuselage parts
- 35-11: Fuselage Canopy Decks
36 - Flight Controls
- 36-13 -> 15: Elevator Control Stops
- 36-11: Slop in the right hand stick
- 36-02 -> 14: Flight Control Push Rods / Elevator Bellcrank / Control Stick Bases / Drilling Control Sticks
37 - Roll Over Structure
OP - Fuselage Optional Kits
- 35-08 -> 35-20: Finally installing the forward fuselage parts to the airframe
- 35-09 ->13: Aft Panel Frame Assembly / 59-02: Power Module Parts / 42-03: Aft Tunnel Cover Modification
- 31-02 -> 03: Installing Duplex Fuel Selector / Fuel Line Brackets
- OP63 - Remote Canopy Release - Mechanism Assembly
- 33-04 -> 10: Brake Hoses
- 34-04: Incorrect Flap Motor Length (the value of VAF Forums & the RV Community)
- 34-02 -> 04: Flap Torque Tubes
- 32-03: Baggage Tie Down Rings - Final Install
- Parking Brake Valve
- 32-07: Flap Motor Brackets - Modification
- Smoke System: Plumbing and Testing
- 32-03: Initial Fit of Baggage Skins / Baggage Tie Downs
- Building a Fuselage Rotisserie
- 29-09: JD-Air Canopy Latch
- 34-04: Alternate Flap Motor
No comments:
Post a Comment